[wii-clip]

WII-CLIP V1 ---> Support D2CKEY AND D2CPRO chips

The Wii-Clip V1 final version looking.





WII-CLIP V1 can support D2CKEY AND D2CPRO chip BOTH! 100% test passed.

Very easy for install, just need put WII-CLIP onto the D2C chip, then solder all pin to pin big points, then finish!


The wii-clip backside details, very high-precision technology guarantee wii-clip can connect each pin 100% well and working stable!

After it, just need put the WII-CLIP onto the Wii motherboard to cover the D2C chipset.




Done! Your Wii is modified! Whole installing process can finish in 2 minutes.




The retail packing:



link : www.wii-clip.com

[Judebox]

Hi,
I have bought a wii-clip presoldered with a d2ckey. I have a wii with a d2c chipset. I have put the wii-clip on the chip as harder as I can. It is now perfectly set over the chipset and the motherboard.
The backups works perfectly when the wii is open (but sometimes I get a black screen). The red light is on and the blue one is blinking.
But when I close the Wii (just the dvd drive over the other part without the screws), it doesn't works anymore. Sometimes I can see the backup on the main screen but when I launch it it goes on a black screen.
I have set the 2 protections against the short cicruit.
Do you have any idea on what the problem could be ?
Thanks for your answers !!

[johnnysu]

subscribed, same thing happened to me. EXACT same thing!

have you covered it up witht e protect label and the blue pice of card that says wii clip?

[johnnysu]

yup, i did

[new2wiiMod]

Hi,
I installed presoldered D2CKey with Wii clip with its protecting lables.
I am able to run the orginal disks fine, I get "cannot read disk" error for backup disk. the chip has green light on and stays on I did not see blue or red light coming on.
I am using Verbatim DVD-R with nero and LG burner.

help appreciated.

[matsterman]

dont use nero, find IMGBURN here or on the internet.

also, burn at 1x

as far as closing goes, you have something that is not in place right because you must be applying too much pressure on something when you close it. Are you sure the drive is sitting correctly in its place? I had alittle trouble with lining it up and did, initially, but it together incorrectly my first time

I have had success with verbatim -r 4.5 and DL. Memorex also worked(made by ritek) at 1x. TDK did not work at any speed, nor did fujifilm. These were burnt on an LG external.

Also, I have a d2cpro on a presoldered wii-clip. make sure the clip is flush against the board. Also, wiggle the chip alittle to get the contacts to touch better.

But first, I would get rid of nero, go to imgburn and and burn at 1x.

[johnnysu]

yes the drive is sitting correctly in place, and i already use img burn...although my burner can burn at a minimum of 4x.....my backups work fine all the time, only when wii is opened though, never when i try to close the wii

[new2wiiMod]

Discovered the clip was not seating properly. I was bit scared at first to push it further down with all that pressure. after fitting it almost flush to the board it started working fine. Verbatim worked, I had few staples dvds those work fine too.
thanks

[johnnysu]

Originally Posted by new2wiiMod

Discovered the clip was not seating properly. I was bit scared at first to push it further down with all that pressure. after fitting it almost flush to the board it started working fine. Verbatim worked, I had few staples dvds those work fine too.
thanks

glad to hear man, enjoy gaming paradise!